Home > Products > Frictionizer

• Retention Aid
• SI-515
• SI-518
• Multi-Wall Low pH Antiskid
• LOAD LOK LPH-35
• Sprayable Frictionalizer/Antiskid
• SPRAY LOK B-16
• SPRAY LOK B-35
• SPRAY LOK M-60
• Flexo Printable Antiskid
• LOADFAST-RTU

LOAD LOK LPH-35
Multi-wall Frictionizer

Look to Silco for the latest technical performance advances in frictionizing compounds and application methods.

• HIGH SLIDE ANGLES – 36º to 42º
• EXTENDED DILUTION RATES – May be diluted up to 6 to 1 with water for maximum economy
• HIGH PRINT QUALITY – No ink smear, no tracking, no streaking, and no blotchy spotting, even on the darkest of inks
• COMPATABLE WITH THE pH IN ALL INK
• ULTRA SMOOTH COATING APPLICATION – for superior and complete surface coverage
• NON SMEARING OR TRACKING – even when applied to very rough paper stock with various pH inks
• FAST EASY CLEAN UP WITH NEW NON-HARDENING FORMULA – Pans and rollers can be completely cleaned with clear plant water. No more need to beat rollers into place with hammers
• NON-DUSTING, NON-GHOSTING – Even on dark colored inks
• PULPABLE AND RECYCLEABLE
• COMPLETE FDA APPROVED INGREDIENT LIST – Based on 21CFR-17.70. LPH-35 uses no live steam in its manufacturing that can contribute to contamination from boiler and steam line treatment chemicals
• NO OBJECTIONAL ODOR – From fungal and biological growth LPH-35 is highly stable and has extended shelf life.
• NONAGGRESSIVE TO FERROUS AND NON-FERROUS METALS
• LITTLE TO NO PAN SEDIMENTATION – Because LPH-35 exhibits a very stable suspension, much less active frictionizer will be found in the bottom of the tray, ending the time consuming expensive job of cleaning out trays
• HELPS ELIMINATE LINE BREAKAGE AFTER RESTARTS

SPRAY LOK B-16
High performance, easy to clean, low misting, Colloidal Silica frictionizer for corrugated boxes

Look to Silco for the latest technical performance advances in frictionizing compounds.

• NO BUILD UP ON SPRAY TIPS OR EQUIPMENT
• LOW MISTING – New extremely low misting formula promotes less build-up, less waste, and more product on the box. Spray Lok will give you higher slide angles at a lower cost
• SAFER FOR PLANT PERSONEL – New Spray Lok contains a unique anti-misting compound that allows for more actual frictionizing material to reach the surface of the box to be treated and not to be suspended into the air to cause potential upper respiratory problems or skin irritation for plant personnel
• SMOOTH NON-MOTTLING COATING – Spray Lok will create a smooth non-mottled coating for superior print quality while providing higher slide angles
• NON-REACTIVE – To most all ferrous and non-ferrous metals as well as paint
• NO EFFECT ON RECYCLING OR RE-PULPING
• HIGH LEVEL OF INDICATION – Plus UV indicatable package is also available
• HIGHLY DILUTABLE – For excellent economy in application
• COMPATABLE – Spray Lok is compatible with most all spray and roller application equipment
• NON-TOXIC – Waste material in most locations can go to the sanitary sewer
• MADE WITHOUT INJECTING LIVE STEAM INTO THE REACTOR – Most silica is manufactured by injecting live stem into the reactor as the silica particle is created or “grown.” Along with the steam comes a number of toxic boiler treatment chemicals. Silco has developed a new process that eliminates the need for live steam and the toxic treatment chemicals associated with live steam.
  

SPRAY LOK is designed for the high speed, cost conscience, converting operations. Spray Lok combines the highest quality frictionizing silica with the easiest ability of use and clean up with plant water. Spray Lok is engineered to give you superior application and cost with the convenience you want.

APPLICATION METHODS
Spray Lok minimizes problems associated with any application method. Spray Lok is engineered to not plug spray tips or dry out on felts, sponges, or rollers. Spray Lok is extremely low misting which minimizes abrasive wear on slitters, scorers, robotic shafts and other mechanical equipment. The dilution ratio and application rate should be verified for adequacy by the end user.

TYPICAL SPECIFICATION

SPRAY LOK M-60
HighPerformance, Easy to Clean,Low Misting,Colloidal Silica Frictionizer for Corrugated Boxes & LinerBoard

Look To Silco2 For The Latest Technical Performance Advances In Frictionizing compounds

• HIGH SLIDE ANGLES - From extended dilution up to 10:1 with water.
• NO BUILD UP ON SPRAY TIPS OR EQUIPMENT
• LOW MISTING - New extremely low misting formula promotes less build-up, less waste, and more product on the sheet. Spray Lok will give you higher slide angles at a lower cost.
• SAFER FOR PLANT PERSONNEL- New Spray Lok contains a unique anti-misting compound that allows more frictionizing material to reach the surface of the box. This helps prevent potential upper respiratory problems and skin irritationfor plant personnel because there is less material in the air.
• SMOOTH NON-MOTTLED COATING - Spray Lok will create a smooth non-mottled coating for superior print quality while providing higher slide angles.
• NON-REACTIVE - to most ferrous and non-ferrous metals as well as paint.
• HIGHLY EFFICIENT, RECYCLEABLE, AND RE-PULPABLE FORMULA
• HIGH LEVEL OF INDICATION - plus UV indictable package is also available.
• CONTROLS ADDED BACK MOISTURE by allowing application with 50% smaller spray tips.
  
• COMPATIBLE - Spray Lok is compatible with most spray and roller equipment.
• HIGHLY STABLE ON THE SHEET which reduces slide angle lost from the reel to the rewind.
• MADE WITHOUT INJECTING LIVE STEAM INTO THE REACTOR - Most silica in manufactured by injecting live steam into the reactor as the silica particle is created or “grown”. Along with the steam comes a number of toxic boiler treatment chemicals. Silco2 has developed a new process that eliminates the need for live steam and the toxic treatment chemicals associated with live steam.
  

Spray Lok M-60 is designed for the high speed, cost conscious, converting operations. Spray Lok combines the highest quality frictionizing silica with the easiest ability of use and clean up with plant water. Spray Lokis engineered to give you superior application and cost with the convenience you want.

APPLICATION METHODS

Spray Lok minimizes problems associated with any application method. Spray Lok is engineered to prevent spray tips from clogging and dry out on felts, sponges, or rollers. Spray Lok is extremely low misting which minimizes abrasive wear on slitters, scorers, robotic shafts, measurement systems, and other mechanical equipment. The dilution ratio and application rate should be verified for adequacy by the end user.

TECHNICAL INFORMATION

Spray Lok is an amorphous colloidal silica product. The presence of Spray Lok can be checked with most available indication solutions out to 10:1 dilution.

SPRAY LOK B-35
High Performance, Easy to Clean, Low Misting Colloidal Silica Frictionizer for Corrugated Boxes & Liner Board

Look To Silco2 For The Latest Technical Performance Advances In Frictionizing compounds

• HIGH SLIDE ANGLES - From extended dilution up to 10:1 with water.
• NO BUILD UP ON SPRAY TIPS OR EQUIPMENT
• LOW MISTING – New extremely low misting formula promotes less build-up, less waste, and more product on the box. Spray Lok will give you higher slideangles at a lower cost.
• SAFER FOR PLANT PERSONNEL - New Spray Lok contains a unique anti-misting compound that allows for more actual frictionizing material to reach the surface of the box to be treated and not to be suspended into the air to cause potential upper respiratory problems or skin irritation for plant personnel.
• SMOOTH NON-MOTTLED COATING – Spray Lok will create a smooth non-mottled coating for superior print quality while providing higher slide angles.
• NON-REACTIVE – to most all ferrous and non-ferrous metals as well as paint.
• HIGHLY EFFICIENT, RECYCLABLE AND RE-PULPABLE FORMULA
• HIGH LEVEL OF INDICATION – plus UV indictable package is also available.
• HIGHLY DILUTABLE – for excellent economy in application.
• COMPATABLE – Spray Lok is compatible with most all spray and roller application
  equipment.
• NON-TOXIC – Waste material in most locations can go to the sanitary sewer.
• MADE WITHOUT INJECTING LIVE STEAM INTOTHEREACTOR – Most silica in manufactured by injecting live steamintothereactor as the silica particle is created or “grown”. Along with the steamcomes a number of toxic boiler treatment chemicals. Silco2 has developed a new process that eliminates the need for live steam and thetoxic treatment chemicals associated with live steam.
  

Spray Lok B-35 is designed for the high speed, cost conscious, converting operations. Spray Lok combines the highest quality frictionizing silica with the easiest ability of use and clean up with plant water. Spray Lok is engineered to give you superior application and cost with the convenience you want.

APPLICATION METHODS

Spray Lok minimizes problems associated with any application method. Spray Lok is engineered to not plug spray tips or dry out on felts, sponges, or rollers. Spray Lok is extremely low misting which minimizes abrasive wearon slitters, scorers, robotic shafts and other mechanical equipment. The dilution ratio and application rate should be verified for adequacy by the end user.

TECHNICAL INFORMATION

Spray Lok is an amorphous colloidal silica product. The presence of Spray Lok can be checked with most available indication solutions out to 10:1 dilution.

LOADFAST-RTU
New Printable Silica Anti-Skid

LOADFAST-RTU is a new printable Silica Anti-Skid designed to be applied at the Flexo. LOADFAST-RTU will provide the highest possible slide angles, while not damaging your anilox rolls or contribute to color distortion.

• PRINTABLE
• LOADFAST-RTU allows you to now print anti-skid on a box or bag in perfect register, with no ink or color distortion and no anilox damage
• HIGH PERFORMANCE With LOADFAST-RTU you are now able to reach slide angles never available from printable materials in the past. Slide angles of36°to 40° on 100% ink coverage are now very achievable
• EASY CLEAN
• LOADFAST-RTU will clean up immediately with clear water, even if left for several weeks between cleaning
• CONVENIENT Simply place a pail of LOADFAST-RTU at a print station and you are ready to apply anti-skid. No dilutions or viscosity adjustment is needed
• ANILOX ROLL COMPATIBLE
• New LOADFAST-RTU will not damage anilox rolls under normal conditions

LOADFAST-RTU now offers both large and small box and sack manufacturers the ability to apply high performance colloidal anti-skid to any box or bag in perfect register. LOADFAST-RTU is ideal for your most demanding customers or for correcting slide angle problems after the box or bag is printed.

TYPICAL SPECIFICATION